RC-Steering Axle Control  for RC-Truck-Trailers (1 or 2 steerable axles)

The trailer deflection to the tractor engine is measured with a potentiometer.
With this deflection one or two servos (individually configured) are controlled for steering one or two steering axles (groups).
There is a dead range for the poti (there is an output for a signalisation lamp). The poti can be deactivated.
Additionally, the servos can be controlled with the RC-transmitter (mixing functionality).
In summary, this RC-Steering Axle Control is a small electronic board for steering a model truck trailer with several functions, all individual configurable.

This electronic module has the following properties:

• HV-conform (up to 16V ! )
  
• For one or two servos (1 or 2 steering axle groups)
• Servo position only with poti    or    poti + RC-transmitter controllable (mixing function)
  
• Every servo individual configurable
• Zero position
  
• Minimum / maximum position
• Rotation direction (servo reverse)
• Rotation speed
  
• Controlling additional with RC-transmitter (mixing poti / RC-transmitter)
• Poti parametrizable
• minimum / maximum position
• minimum / maximum dead range
  
• mounting zero position
• Poti can be deactivated with a switching input
• Servo 2 can be deactivated with a switching input (moves to configured zero position)
• dead range indicator output
  

 
There are two different types available, with the same functionality:

For requests and orders please write at  info@hamatronic.ch .

Accessories

For the RC-Steering Axle Control there are cable sets incl. mechanical poti available:

Also as accessory for the RC-Steering Axle Control there are cable sets incl. electronical poti available, that detects the centric rotation of a magnet over a sensor- without contact.

A distance of a few millimeters from the sensor is possible, it depends on the size of the magnet. The magnet can be bonded or placed on a ferrous surface (e.g. a screw head). 

The RC steering axle control can also be connected to the steerable king pin with potentiometer from Pistenking. As accessory a  connection adapter is available for this to the RC steering axle control.

Do you need an other cable length, an other poti type or an other magnet?
For requests and orders please write at  info@hamatronic.ch .

RC-Pressure Controller

Air pressure controller for RC-function models (e.g.  airsuspension, brakes, interlocks, etc.).
The RC-air pressure controller runs the air pump until the targe value is reached. The actual value is measured by a pressure sensor, and the target value is adjusted with a poti.
When the air pressure falls under the target value (incl. hysteresis) the air pump starts again.
If the pressure rises over the target value (incl. hysteresis), the mangetic valve opens and the air flows out until the target value is reached.
Optionally a RC-receiver can be connected for controlling the air pressure with the RC-transmitter from  0 bar to the target value adjusted with the poti.
It is possible to use the delivered components (air pump, magnetic valve 3.3V) or other components (max. 1000 mbar).

This electronic module has the following properties:

• HV-conform (up to 16V ! ) with the appropriate components (air pump/ magnetic valve) 
  
• Autonomous operation without RC-transmitter
  
• Optionally air pressure variable by RC-transmitter
  
• Appropriate air pump: 3.3V  or  supply voltage up to 16V
• Appropriate magnetic valve: 3.3V  or  supply voltage up to 16V
• Default state magnetic valve selectable (open or closed)
  
• Supplied accessories
  
• Air pump 3.3V with cable 30cm
  
• Magnetic Valve 3.3V with cable 30cm
• Air hose (inner diameter 2mm), 150cm
  
• Receiver cable  30cm
  

 
There are two different types available, with the same functionality:

For requests and orders please write at  info@hamatronic.ch .

RC-Motor-Controller

RC - DC motor controller for controlling spindles and lifting cylinders.
It includes a switch-off function when the motor is blocked (e.g. for spindles without limit switches).
If the motor is blocked, the controller is automatically switched off in a self-learning manner, no limit switches are necessary.

This RC motor controller has the following features:  

• self-lerning adaptation to the connected motor - everything is automatically
  
• HV-capable (up to 13V ! ) 
  
• wide voltage range from drive battery (4.5V to 17V)
• without BEC
  
• motor-specific start-up behaviour (is measured when switching on)
• motor brake at stop position
  
• status feedback with sound
  
• blocking current/ sound output can be optionally parameterised with remote control
  
• several controller protection mechanisms (can be reset during operation):
• runtime limited
  
• short-circuit protection
• overcurrent shutdown
• overheating protection
• protection against incorrect battery voltage (not all types)
• reverse polarity protection (not all types)

Two different types are available:

For requests and orders please write at  info@hamatronic.ch .

RC-Hydraulicpump-Signalmixer

This  signalmixer compares to RC-signals (synchronous or asynchronous) and forwards the "bigger"/ "smaller" to the signal output.
This RC-Signalmixer is designed for connect to servonaut BMA-moduls to one motor controller for the hydraulic pump. The Hydraulic pump switchs off only when the modules switchs off both of them.

This electronic module has the following properties:

• HV-conform (up to 16V ! )
• Process 2 input signals to one output signal (for motor controller)
• Selectable priority ("bigger" or "smaller" input signal) for other applications
  
• Suitable for self-learning motor controller
• Motor controller with BEC are usable too
  

Accessories

The following connection cables are available (other cable length on request):

For requests and orders please write at  info@hamatronic.ch .

Servo-Standby-Modul

Switches the servo off after the servo position is reached. As soon as a new servo signal is present, the servo starts again.
Function (for analogue und digital servos):

• Reduction of servo current consumption
• Reduction of servo noise 
  
• Servo pulse doubling (more servo power)
  

The servo-standby-module is connected between receiver and servo.
If the servo position does not change within the adjustable delay time, the servo is driven less/ no longer and reduces the current/ noise (holding force of the servo becomes weaker ! ).
With a new servo signal, the servo is controlled normally again; then the delay time starts again.
The module can also be used to double the pulse frequency for more servo power in normal operation; in this mode normal pulses are present AFTER the delay time.

ATTENTION: Function can not be guaranteed for all servos! 

Do you need an other cable length?
For requests and orders please write at  info@hamatronic.ch .

RC-Switch

Electronic module for switching an electric device on/ off.
The switching position is adjustable with a poti.
 
The following variants are available:

Do you need an other supply voltage range or an other cable length?
For requests and orders please write at  info@hamatronic.ch .

Location Beeper

An emergency landing in the cornfield? An off-field landing behind bushes?
No problem ... but I can't find the model plane?

With a loud interval beeping sound this Location Beeper helps you to find your model plane.
The beep starts when the RC-transmitter is switched out (the RC-receiver does not send impulses again, i.e. without failsafe).
Additionally there can be defined a switching point for starting the beeping sound with the RC-transmitter (mode for failsafe-receiver).

The following variants are available:

Do you need an other supply voltage range or an other cable length?
For requests and orders please write at  info@hamatronic.ch .

RC-Flashing Lights

These electronic modules generate flashing patterns of warning lights.
There are blinking and flashing light patterns, with one or two LEDs, alternating blinking/ flashing available.
It is possible to solder additional LEDs (or other lamps).

The flashing light is switched on by RC-transmitter, the switching point is adjusted with a poti.
If the poti position is on the final position, the flashing light is always on, i.e. if it is supplied, it starts to flash and does not need a RC-transmitter.

The following variants are available:

Do you need several LEDs or an other cable length?
For requests and orders please write at  info@hamatronic.ch .

Accessories

For the Flashing Lights the following additional LED's (incl. cable and series resistor) are available: